ABU DHABI NATIONAL OIL COMPANY (ADNOC) GHASHA CONCESSION PROJECTS

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No:

67-00106

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

COMPANY DOC No: 1-CF0000-40-SPE-0032-00

Rev. B3

ABU DHABI NATIONAL OIL COMPANY (ADNOC) GHASHA CONCESSION PROJECTS

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CONTRACTOR Document Number: CF0000-1085351

B3

10/04/2025

IFA

Issued for COMPANY Approval

B2

24/01/2025

IFA

Issued for COMPANY

Approval

B1

29/11/2024

IFA

A1

04/09/2024

IFR

Issued for COMPANY Approval

Issued for COMPANY Review

C. Zuliani V. Cavaliere A. Massoni C. Copelli

C. Zuliani V. Cavaliere A. Massoni C. Copelli

C. Zuliani V. Cavaliere A. Massoni C. Copelli

C. Zuliani V. Cavaliere A. Massoni C. Copelli

Rev

Date (DD/MM/YYYY)

Status

Status Description

PREPARED

CHECKED

APPROVED 1

APPROVED 2

This Document is intended for use by ADNOC and its nominated Consultants, Contractors, Manufacturers and Suppliers.

DOCUMENT CLASS – 1 Page 1 of 17

       Uncontrolled When Printed

ABU DHABI NATIONAL OIL COMPANY (ADNOC) GHASHA CONCESSION PROJECTS

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

COMPANY DOC No: 1-CF0000-40-SPE-0032-00

Rev. B3

HOLD

Section

Description

HOLD LIST

DOCUMENT CLASS – 1 Page 2 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

TABLE OF CONTENTS

PROJECT OVERVIEW … 4

1.1

EPC for HAIL & GHASHA Development Project … 4

PURPOSE … 5

DEFINITIONS AND ABBREVIATIONS … 5

3.1

3.2

Definitions … 5

Abbreviations … 5

REFERENCE DOCUMENTS … 6

ORDER OF PRECEDENCE … 7

GENERAL AND TECHNICAL REQUIREMENTS … 7

DESIGN LIFE … 8

ENVIRONMENTAL CONDITIONS … 8

TECHNICAL SPECIFICATION … 8

9.1

Breathing Air Station (BAS) … 10

COORDINATION WITH SUB-VENDORS … 13

SCOPE OF SUPPLY … 13

QUALITY ASSURANCE, INSPECTION, TESTING AND CERTIFICATION … 13

LABELLING, PAINTING AND PROTECTIVE COATING … 14

PREPARATION OF SHIPMENT, PRESERVATION AND TRANSPORTATION … 14

PROJECT SPARE PARTS REQUIREMENTS … 14

SPECIAL TOOLS… 15

DRAWING AND DOCUMENTATION … 15

GUARANTEE … 16

APPENDIX 1 - SAFETY AND LIFE SAVING EQUIPMENT DATASHEETS … 17

DOCUMENT CLASS – 1 Page 3 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

PROJECT OVERVIEW

1.1

EPC for HAIL & GHASHA Development Project

The Hail & Ghasha Development (HGD) Project is of strategic importance to the Emirate of Abu Dhabi. The Project will develop the untapped oil and gas reserves from the highly sour Hail and Ghasha fields. Production is targeted to start by Q4 2027 with sustainable production of 1 BSCFD of Raw Gas, and max production of 82.5 MSBPD of Oil, 76.3 MSBPD of Condensate, 9000 TPD of Sulphur and 5030 TPD of NGL. In addition, Project will capture 1.52 million tonnes of CO2 per year taking ADNOC’s committed investment for carbon capture capacity. The Hail and Ghasha fields are situated offshore ABU DHABI about 140 km away from ABU DHABI mainland in water depths varying from 0 to 15 meters.

The HGD Project comprises the following:

• Artificial Islands Construction;

• Offshore package – EPC 01: Offshore Drilling Centres (DCs), Subsea Pipelines, Umbilicals, Power Cable Connections, Seawater Intake Structure, Bridges, Risers, Flare Structure, facilities at Ghasha Offshore Processing Plant (“GOP”);

• Onshore package – EPC 02: Manayif Onshore Processing Plant (“OPP”), Manayif

Utilities, Offsite Pipelines & Tie-ins, Main Control and Other Buildings.

The HGD Project will be executed in a single phase approach. It will start production from three Drilling Centres (Reeah, Jzool & Seebah) in Ghasha Field to GOP and from Gaff Island in Hail Field to OPP. Remaining Drilling Centres, gas injection, and other associated facilities will be developed in ‘future’ to sustain production from Hail & Ghasha fields.

Figure 1 - Hail & Ghasha Fields

DOCUMENT CLASS – 1 Page 4 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

PURPOSE

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

This specification and the attached datasheets set the minimum requirements for the design, manufacture, assembly, quality control, inspection, testing and supply of the Safety and Life Saving equipment to be provided for the PROJECT. This specification is for GOP and the DC.

These equipment shall be in strict accordance with this technical specification and all other documents, Codes & Standards referred to in this specification and the respective requisition. Any exception to the requisition documents and referred Codes & Standards shall be clearly listed in VENDOR’s quotation in a separate section.

DEFINITIONS AND ABBREVIATIONS

3.1

Definitions

COMPANY

Abu Dhabi National Oil Company (ADNOC)

CONTRACTOR

Unincorporated Joint Venture NPCC - SAIPEM

PROJECT

Hail and Ghasha Development Project

SUBCONTRACTOR

VENDOR/SUPPLIER

Any Person approved in writing by the COMPANY to whom execution of any part of the Works is subcontracted by the CONTRACTOR and any other subcontractors of any tier of such Person, and includes its legal successors and/or permitted assigns.

A supplier of Materials in connection with the Works including related documentation and services, where necessary.

3.2

Abbreviations

ADNOC

AGES

BAS

DC

EEBA

EPC

FM

GOP

HGD

Abu Dhabi National Oil Company

ADNOC Group Engineering Standards and Specifications

Breathing air Station

Drilling Center

Emergency Escape Breathing Apparatus

Engineering, Procurement and Construction

Factory Mutual Group

Ghasha Offshore Processing

Hail & Ghasha Development

DOCUMENT CLASS – 1 Page 5 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

HSE

IP

ISO

MMSCFD

SCBA

SOLAS

SS

TPI

UAE

Health Safety and Environment

Ingress Protection

International Standards Organization

Million Standard Cubic Feet per Day

Self-Contained Breathing Apparatus

Safety of Life at Sea

Stainless Steel

Third Party Inspection Authority

United Arab Emirates

REFERENCE DOCUMENTS

Sl. No.

Document No.

Document Title

1. API 521

2. HSE-GA-ST07

Pressure-Relieving and Depressuring Systems HSE Design Philosophy Standard

3. HSE-OS-ST20

Personal Protective Equipment

4. HSE-OS-ST21

5. AGES-SP-03-001

1-CF0000-40-PHL-0002-00

Management of Hydrogen Sulfide (H2S) Standard Escape, Evacuation, Rescue & Life Saving Appliances (EER & LSA) Specification HSE Design Philosophy

1-CF0000-40-MOR-0043-00 Material Requisition For Breathing Air

Stations 1-CF0000-40-MOR-0042-00 Material Requisition For Safety And Life

1-CF0000-59-PHL-0001-00

Saving Equipment Basic Engineering Design Data (BEDD)

1-CF0000-25-SPE-0702-00

Painting, Coating And Lining Specification

1-GH5161-04-PID-1005-01

1-CF0000-40-SPE-0039-00

1-GH5167-04-PID-1050-00

1-GH5167-04-PID-1014-00

1-CF0000-25-SPE-0702-00

Piping & Instrument Diagram - OFFSHORE UNIT 61 - (GOP) Chananiz Isl. Potable Water Distribution Technical Specification - Breathing Air System Piping & Instrument Diagram Offshore Unit 67 - (GOP) Breathing Air Distribution Piping & Instrument Diagram Offshore Unit 67 - (GOP) Breathing Air Distribution Painting, Coating and Lining Specification

16. ADNOC Doc. No. PK1-

Attachment 2 to Scope of Work Narratives

03.B.04 17. ANSI Z358.1

Emergency Eyewash and Shower Equipment

DOCUMENT CLASS – 1 Page 6 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

Sl. No.

Document No.

Document Title

18. SOLAS 74/96

ISO 12402-7

20. EN 402:2005

21. EN137: 2006

ISO 23261-3

International Convention for the Safety of Life at Sea Personal flotation devices

Respiratory protective devices - lung governed demand self-contained open-circuit compressed air breathing apparatus with full mask or mouthpiece assembly for escape - requirements, testing, marking Respiratory protective devices. Self- contained open-circuit compressed air breathing apparatus with full face mask. Requirements, testing, marking Health informatics - Requirements for accessing digital medicinal products information by using the existing data carrier

ORDER OF PRECEDENCE

Design and engineering for the Facilities shall be undertaken in accordance with regulations, codes, standards and specifications in the order of precedence stated below:

• United Arab Emirates (UAE) Local Codes, Laws and Regulations.

• COMPANY HSE Standards.

• Project Specifications / Datasheets as approved by COMPANY.

• COMPANY Group Engineering Standards and Specifications (AGES)

• ADNOC Offshore and ADNOC Onshore Specifications and Standards

•

International Codes & Standards.

In the event of conflict between various general standards and specifications, precedence shall be in the order listed above with local laws and regulations carrying the highest priority. However, VENDOR shall review the merits of any conflicting specifications and provide recommendation on the most appropriate specification to observe. If the recommendation the above stated order of precedence, CONTRACTOR/COMPANY shall review the recommendation and provide the final decision on which specification/standard shall be adopted for PROJECT use.

is contrary

to

GENERAL AND TECHNICAL REQUIREMENTS

The specification is complementary to requirements of legislative requirements, guidance notes issued by any authority and documents referenced herein.

This specification is general in nature and shall be read in conjunction with attached data sheets, relevant codes and standards, COMPANY/INTERNATIONAL standards, specifications and documents listed in Section 4.

VENDOR shall refer also to the relevant procurement instructions concerning the manufacture, material/equipment selection, inspection and testing, painting and

DOCUMENT CLASS – 1 Page 7 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

documentation relating to the scope as detailed in the document 1-CF0000-40-MOR- 0043-00 and 1-CF0000-40-MOR-0042-00.

VENDOR is deemed to be in full compliance with all specifications applicable in this PROJECT. It shall be mutually understood that any proposal is based on equipment which is in strict compliance with the requirements of this specification.

VENDOR must complete all missing information of the specification or data sheet marked with (*).

The equipment offered by the VENDOR shall be of proprietary design and manufacture and will comply and be proven in accordance with the Codes and Standards listed in Section 4 of this specification.

The safety and life saving equipment specification are required for use on Offshore. VENDOR shall provide all necessary bracket/fasteners/mounting devices for equipment installation.

The specified equipment constitutes the minimum required. The VENDOR shall provide all the elements necessary to ensure correct operation of the equipment, even those which would not be explicitly mentioned, and according to the limit of supply defined.

The design shall address the operating conditions, in particular high Ultra-Violet radiation levels, high ambient temperature, humidity and corrosive environment. The requirements of these conditions shall be fully compensated for, both in the design and in the construction materials of the equipment.

Pictorial safety signs shall be supplied along with each Safety and Life Saving equipment. Safety signs shall be in both Arabic and English.

DESIGN LIFE

The equipment shall be designed for a life of 30 years based on correct and regular preventive maintenance in accordance with manuals supplied by the VENDOR.

ENVIRONMENTAL CONDITIONS

All Safety and Life Saving equipment shall be suitable for operation under Environmental Conditions defined in BASIC ENGINEERING DESIGN DATA (BEDD) (Doc. No. 1- CF0000-59-PHL-0001-00).

TECHNICAL SPECIFICATION

The Safety and Life Saving equipment shall comply as a minimum with the data sheets attached in Appendix 1.

No.

Safety description

and

life Saving Equipment

Ref. Datasheet No./Section

Breathing Air Station (BAS)

Appendix-1 – A1/ section 9.1

DOCUMENT CLASS – 1 Page 8 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

No.

Safety description

and

life Saving Equipment

Ref. Datasheet No./Section

Safety Shower Containing Integral Eye Wash

Appendix-1 – A2

Standalone Safety Shower Containing Integral Eye Wash (at DC)

Appendix-1 – A3

Portable Safety Shower Containing Integral Eye Wash (at DC)

Appendix-1 – A4

Wind Socks With Lights

Appendix-1 – A5

Lifebuoys

Life Raft

Life Jacket

Emergency apparatus (EEBA) - mask type

escape

breathing

Appendix-1 – A6

Appendix-1 – A7

Appendix-1 – A8

Appendix-1 – A9

Light Weight Self Contained Breathing Apparatus (SCBA)

Appendix-1 – A10

Helicopter Crash Equipment Cabinet

Appendix-1 – A11

Chemical Kit

Appendix-1 – A12

First Aid Kit (FAK)

Appendix-1 – A13

Electrical Safety Kit buildings)

(inside

the

Appendix-1 – A14

Portable Eyewash Station (inside the buildings)

Appendix-1 – A15

Stretcher (inside the Fire Point Shelter) Appendix-1 – A16

Fire Blanket (inside the Fire Point Shelter/ Ready for operational phase)

Appendix-1 – A17

Face Shield Mask (inside the Fire Point Shelter)

Appendix-1 – A18

Wheeled Air Loop Trolleys (Ready for operational phase)

Appendix-1 – A19

DOCUMENT CLASS – 1 Page 9 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

No.

Safety description

and

life Saving Equipment

Ref. Datasheet No./Section

Heat Stress Monitor operational phase)

(Ready

for

Appendix-1 – A20

Noise Monitor Dose Meter (Ready for operational phase)

Appendix-1 – A21

Safety Gloves (Ready for operational phase)

Appendix-1 – A22

Hand held megaphone (Ready for operational phase)

Appendix-1 – A23

Rechargeable operational phase)

torches

(Ready

for

Appendix-1 – A24

Wind sock (Ready phase)

for operational

Appendix-1 – A25

Rescue basket (Ready for operational phase)

Appendix-1 – A26

Safety operational phase)

harnesses

(Ready

for

Appendix-1 – A27

Complete Firemen’s Equipment Set

Appendix-1 – A28

Scramble Net

Appendix-1 – A29

Chemical Kit Battery Room

Appendix-1 – A30

Multiple gas detectors

Appendix-1 – A31

Portable multiple gas detectors with alarm

Appendix-1 – A32

It is remarked that the Safety Equipment listed in Appendix 2 of Scope of Work Narratives and required to be specifically installed/provided at CLQ are not included in this specification, since CLQ is not in JV Contractor scope.

9.1

Breathing Air Station (BAS)

Breathing Air Station (BAS) will be installed as terminal piece of breathing air network within units in Red Zone.

Following documents shall be used as technical references for BAS design:

• Technical Specification – Breathing Air System (ref. 12)

DOCUMENT CLASS – 1 Page 10 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

• Piping & Instrument Diagram Offshore Unit 67 - (GOP) Breathing Air Compressor

Package (ref. 13)

• Piping & Instrument Diagram Offshore Unit 67 - (GOP) Breathing Air Distribution (ref.

Each BAS shall include:

• Manifold in stainless steel AISI 316 with four quick-disconnect/connect socket and plug assembly that offers an automatic air flow shut-off in case of disconnection and an easy connection to the air supply hose;

• 1 pressure gauge;

• Protection caps for each outlet suitable for desert environment and resistant to

presence of hydrogen sulphide;

• NPT (National Pipe Thread) female thread connection to breathing air network

according to ASME B1-20-1(1983) at each end;

• Painting according to AGES-SP-07-004 and Project Document 1-CF0000-25-SPE- 0702-00 “Painting, Coating and Lining Specification” (stainless steel element shall not be painted).

• Hoses permanently connected to the manifold

• Protection box for both manifold, pressure gauge and hoses

VENDOR shall design breathing air station in order to be easily installed on handrail of staircase or module or piperack.

VENDOR shall prepare a general arrangement drawing for CONTRACTOR approval before proceeding with BAS fabrication.

The diameter of BAS connection to breathing air network shall be 3/4’’ Quick- disconnect/connect socket and plug assembly shall be suitable for the connection to Self- Contained Breathing Apparatus.

Each component shall be suitable for the installation in desert environment.

Outlet connections shall be designed in order to avoid that air-line could be connected to wrong network.

The hoses shall be permanently connected to the manifold. Both the manifold and the hoses shall be located inside a box to be protected by the external environment.

Hoses

Each hose shall be supplied in compliance with following requirements:

• 20 m or 30 m in length;

• Sized in order to guarantee peak flow required by selected SCBA (composed by facemask, air cylinder and automatic switch over valve) considering the minimum/maximum working pressure of automatic switch-over valve mounted on SCBA

• Suitable for breathing air application (proper certification shall be supplied)

• Suitable for desert environment and presence of hydrogen sulphide in atmosphere

(VENDOR shall indicate how hose could guarantee it in his technical proposal)

DOCUMENT CLASS – 1 Page 11 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

• Equipped with quick-connection couplings. The quick-connection coupling shall be selected for the connection to selected SCBA for the PROJECT (airline Hansen connection as per HSE-OS-ST20).

• All requirements stated in EN 14593-1 and EN 14594 respected.

• The hose shall able to auto role when released.

Identification label (suitable for desert environment) shall be equipped with each hose.

Each hose’s quick connection coupling shall be equipped with protective caps suitable for desert environment and presence of hydrogen sulphide.

Boxes

Both the BAS and the hoses shall be stored inside a box. The box shall be supplied in compliance with the following requirements:

• Weather-proof closed cabinet with door (provided with fixing devices), considering the direct exposure to sunlight and environmental/design conditions as described in Basic Engineering Design Data (BEDD);

• designed to store four (nos. 4) 20m/30m hoses (depending by the cases);

• Painted according to the Project Specification.

If painting specification 1-CF0000-25-SPE-0702-00 “Painting, Coating and Lining Specification” should be not applicable for breathing air hose boxes, VENDOR shall supply all information related to painting procedure for COMPANY approval in the technical documentation. If VENDOR provides hose boxes in reinforced fiberglass, they shall be covered with top coat for UV protection according to Painting Specification

The boxes shall be supplied with suitable fixing devices.

A plate of corrosion resistant material, engraved with a list of the contents, shall be attached to the door of each hose box (English and Arabic language).

For further detail refer to Appendix-1 – A1

Pressure gauge

Indicating Scale shall be suitable to monitor pressure up to a value higher than design pressure of BAS piping. Front glasses shall be anti-scratch and shatter proof safety glass.

Generally, element material shall be AISI 316 type (AISI 316L for wetted parts). Steel materials, where requested in individual technical specification, shall be in accordance with NACE MR 01-75 requirements. Case material shall be AISI 316. Pressure gauge shall have zero adjustment.

Over range protectors shall be provided by VENDOR where the design pressure exceeds the maximum over range pressure.

The supplier shall perform calibration and alignment of all instruments before shipment.

Minimum tightness degree shall be IP 65.

Sunshade for pressure gauge shall be provided if required to meet environmental conditions. Sunshade shall be 316 stainless steel painted in accordance with Project Specification 1-CF0000-25-SPE-0702-00 “Painting, Coating and Lining Specification”.

DOCUMENT CLASS – 1 Page 12 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

All field instruments shall be suitable for Zone 1, Gas Group IIB and Temperature class T3.

For further detail refer to Appendix-1 – A1

COORDINATION WITH SUB-VENDORS

VENDOR shall coordinate and solve any problem with his SUB-VENDORS. He will guarantee and be entirely responsible for the performance and the use of the equipment being supplied.

SCOPE OF SUPPLY

The scope of supply shall include, but not necessarily be limited to the following:

Design, Engineering, fabrication and supply of all equipment specified in this

• specification, as specified in technical specification (Appendix-1).

All necessary bracket/fasteners/mounting devices for equipment installation on

• Offshore.

•

•

Shop testing and witness testing (if required).

Inspection, quality assurance/quality control.

• Packing, marking, labelling and preparation for shipment, as per required in the document “Material Requisition For Breathing Air Stations” – doc. 1-CF0000-40-MOR- 0043-00 and “Material Requisition For Safety And Life Saving Equipment” - 1-CF0000-40- MOR-0042-00.

• Spare parts, special tools, preparation of document/drawings as per required in the document “Material Requisition For Breathing Air Stations” – doc. 1-CF0000-40-MOR- 0043-00 and “Material Requisition For Safety And Life Saving Equipment” - 1-CF0000-40- MOR-0042-00.

Certifications, as per requirements specified in Equipment Requisition/ Datasheet,

• shall remain valid when reaching site.

•

•

Mechanical and performance guarantees.

For further details refer to the equipment datasheets in the attachement

QUALITY ASSURANCE, INSPECTION, TESTING AND CERTIFICATION

The VENDOR shall comply with Quality Assurance and Quality Control requirements specified in “Material Requisition For Breathing Air Stations” – doc. 1-CF0000-40-MOR- 0043-00 and “Material Requisition For Safety And Life Saving Equipment” - 1-CF0000-40- MOR-0042-00.

The following shall be made available, as applicable:

•

•

Certificate of Conformity

Type Approval Certificate

DOCUMENT CLASS – 1 Page 13 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

The VENDOR shall make available without charge all necessary equipment and facilities required by CONTRACTOR/COMPANY’s Representative in assisting in inspection and testing.

The equipment shall be supplied under a quality system satisfying the applicable ISO 9001:2015 series, or agreed equivalent standard provisions, appropriate to the goods and services provided.

LABELLING, PAINTING AND PROTECTIVE COATING

All equipment items shall be protected against damage, which might be expected to occur in transport, storage, during installation and commissioning.

Surface preparation, priming and finishing shall be suitable to long term exposure to a marine environment and the ambient climatic conditions. The painting shall be in accordance with the Painting, Coating And Lining Specification (Doc.No. 1-CF0000-25- SPE-0702-00).

The VENDOR shall supply with each item of equipment, a stainless steel (or equivalent material as stated in the data sheet) tag indicating the following information:

•

•

•

•

Manufacturer’s Name

Model Number

Order Number

Equipment Tag Number

The VENDOR shall provide clearly visible manual operation instructions, instrument tagging and component identification labels.

For further detail refer to “Material Requisition for Breathing Air Stations” – doc. 1-CF0000- 40-MOR-0043-00” and “Material Requisition for Safety and Life Saving Equipment” - 1- CF0000-40-MOR-0042-00

PREPARATION OF SHIPMENT, PRESERVATION AND TRANSPORTATION

All equipment shall be prepared for shipment. The packaging of equipment shall comply with the requirement set in the “Material Requisition for Breathing Air Stations” – doc. 1- CF0000-40-MOR-0043-00” and “Material Requisition for Safety And Life Saving Equipment” - 1-CF0000-40-MOR-0042-00.

PROJECT SPARE PARTS REQUIREMENTS

The VENDOR shall provide pre-commissioning and commissioning/start-up spare parts, if required, as part of the scope of supply.

The VENDOR shall submit a list of two (2) years operational and insurance spares, if any.

For detail refer to Material Requisition for Breathing Air Stations” – doc. 1-CF0000-40- MOR-0043-00” and “Material Requisition for Safety And Life Saving Equipment” - 1- CF0000-40-MOR-0042-00

DOCUMENT CLASS – 1 Page 14 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

SPECIAL TOOLS

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

VENDOR shall provide all necessary special tools required for installation, commissioning and maintenance of all the equipment.

For detail refer to Material Requisition for Breathing Air Stations” – doc. 1-CF0000-40- MOR-0043-00” and “Material Requisition for Safety And Life Saving Equipment” - 1- CF0000-40-MOR-0042-00

DRAWING AND DOCUMENTATION

At the time of bid, Vendor shall provide as a minimum the information required at the section 16 of the documents “Material Requisition for Breathing Air Stations” – doc. 1-CF0000-40- MOR-0043-00” and “Material Requisition for Safety And Life Saving Equipment” - 1- CF0000-40-MOR-0042-00.

During execution phase, Vendor shall provide as minimum the document required at the section 9 of the documents “Material Requisition for Breathing Air Stations” – doc. 1- CF0000-40-MOR-0043-00” and “Material Requisition For Safety And Life Saving Equipment” - 1-CF0000-40-MOR-0042-00.

Specifically, the following it is highlighted:

• The English language shall be used for all documents relevant to this supply such as drawings, calculations, specifications, datasheets, certificates, manuals, labels, name plates and correspondence.

• The VENDOR shall submit for approval, all listed drawings / documents, strictly in accordance with the agreed schedule and program. In addition, the presentation of drawings shall be such that all component parts of items within the system can be located and identified for maintenance purposes.

•

All dimensions critical to correct installation shall be shown.

COMPANY/CONTRACTOR’s approval shall in no case relieve VENDOR of his

• responsibility for the functionality and completeness of the supply.

In addition to the documents agreed in the SDRL, the VENDOR shall provide any

• other documents deemed necessary during the execution phase of the project.

COMPANY/CONTRACTOR’s approval shall in no case relieve VENDOR of his

• responsibility for the functionality and completeness of the supply.

English and Arabic language shall be used for operating instructions. The

• International System of Units (SI) shall be used for all measurements.

Major vendor deliverables to be provided are shown below:

•

•

•

•

•

List of Vendors documents and drawings (SDRL)

Equipment list

Equipment data sheets

Drawings of Auxiliaries and Itemized Equipment Supplied Loose

Detailed Drawings

DOCUMENT CLASS – 1 Page 15 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

•

•

•

•

•

•

•

•

•

•

•

General Arrangement Drawings

Bulletins and Catalogues

Special Precautions for Handling prior and during Erection

Recommendations for Storage prior and after Erection

Installation Start-up, Commissioning and Operating Manuals

Material Certificates

Engineering Procurement Manufacturing and Test Schedule

Sub-Vendors and Main Suppliers List

Test certificate and Performance certificate

Packing List with Packing Notes

Vendor Data book for various stages

GUARANTEE

The VENDOR shall be responsible for providing guarantee against defects in design, materials as required in Material Requisition For Breathing Air Stations” – doc. 1-CF0000- 40-MOR-0043-00” and “Material Requisition For Safety And Life Saving Equipment” - 1- CF0000-40-MOR-0042-00.

DOCUMENT CLASS – 1 Page 16 of 17

       Uncontrolled When Printed

COMPANY PROJECT No: 4700021770

CONTRACTOR PROJECT No: 67-00106

COMPANY DOCUMENT No. 1-CF0000-40-SPE-0032-00

HAIL & GHASHA DEVELOPMENT PROJECT PACKAGE 1 – OFFSHORE FACILITIES

Rev

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

B3

APPENDIX 1 - SAFETY AND LIFE SAVING EQUIPMENT DATASHEETS

DOCUMENT CLASS – 1 Page 17 of 17

       Uncontrolled When Printed

APPENDIX 1- A1

BREATHING AIR STATION (BAS)

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

MANIFOLD OUTDOOR NOTE 4

AMBIENT TEMPERATURE

HUMIDITY ATMOSPHERE AIR TEMPERATURE OPERATING PRESSURE DESIGN PRESSURE

NO. OF OUTLETS

CONNECTIONS TYPE

CONNECTIONS SIZE WEIGHT FRAME MATERIAL

STANDARD LENGHT

TYPE

BOXES

OPERATING CONDITIONS

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND °C BARG

22 0/8.5 13

BARG

DESCRIPTION

4

THE MANIFOLDS WILL BE SUPPLIED WITH QUICK- DISCONNECT/CONNECT SOCKET AND PLUG ASSEMBLY THAT OFFER AN AUTOMATIC AIR FLOW SHUT-OFF IN CASE OF DISCONNECTION AND AN EASY CONNECTION TO THE PORTABLE AIR SUPPLY HOSE. BREATHING AIR CASCADING SYSTEM MANIFOLD CONNECTION TYPE SHALL BE ‘Y’ TYPE AND STANDARD HANSEN TYPE QUICK CONNECT/DISCONNECT COUPLINGS SHALL BE PROVIDED AT THE BREATHING AIR MANIFOLDS. HOSE SHALL BE ALWAYS CONNECTED PERMANENTY TO THE MANIFOLD THE HOSE SHALL BE ABLE TO AUTO ROLE IF RELEASED 3/4” (REFER TO 1-GH5167-04-PID-1050-01/02/030/04/05) NOTE 5 * *

HOSES

EN14593-1/ EN 14594 20/30M

THE HOSES WILL BE CONNECTED ON ONE END TO BREATHING TUBE OF THE RESPIRATOR AND ON THE OTHER END TO THE OUTLET CONNECTIONS OF THE MANIFOLDS IN THE BREATHING AIR STATION. VENDOR TO ENSURE THAT HOSES CONNECTION ARE COMPATIBLE WITH SCBA CONNECTION AND MANIFOLD CONNECTION

HOSE BOXES SHALL BE SUPPLIED WITH SUITABLE FIXING DEVICES. A PLATE OF CORROSION RESISTANT MATERIAL, ENGRAVED WITH A LIST OF THE CONTENTS, SHALL BE ATTACHED TO THE DOOR OF EACH HOSE BOX (ENGLISH AND ARABIC LANGUAGE).

TEST

TEST CERTIFICATES AND RELEVANT APPROVALS SHALL BE PROVIDED

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. MATERIAL USED SHALL BE SUITABLE FOR MARINE, HUMID, SALINE ATMOSPHERE WITH AIR-BORNE DUST AND SAND (OUTDOOR), AND POTABLE WATER SERVICE
3. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
4. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT 5, THE DIAMETER OF BAS CONNECTION TO BREATHING AIR NETWORK SHALL BE 3/4’’ QUICK-DISCONNECT/CONNECT SOCKET AND PLUG ASSEMBLY SHALL BE SUITABLE FOR THE CONNECTION TO SELF-CONTAINED BREATHING APPARATUS.

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

1

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

APPENDIX 1- A2 SAFETY SHOWER CONTAINING INTEGRAL EYE WASH

SHOWER + EYE WASH STATION WITH CHILLER UNIT OUTDOOR NOTE 9

OPERATING CONDITIONS

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE WATER TEMPERATURE OPERATING PRESSURE OF SAFETY SHOWER DESIGN PRESSURE OF SAFETY SHOWER OPERATING PRESSURE OF POTABLE WATER SYSTEM DESIGN PRESSURE OF POTABLE WATER SYSTEM FLOW RATE WATER TANK CAPACITY CHILLER UNIT SELF DRAINING BACTERIOSTATIC ADDITIVE POWER REQUIREMENTS

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND °C BARG

OPERATING AMBIENT (NOTE 7 & 8) * * MIN 2, NORMAL 4, MAX 5 11

BARG

BARG

BARG 76 LPM FOR SHOWER AND 1,5 LPM FOR EYE WASH 1200 LITER (MINIMUM) YES (NOTE 16) YES YES (VENDOR TO INFORM THE REQUIREMENT) *

STANDARD

ACTUATOR MINIMUM DISCHARGE TIME ALARM WEIGHT FRAME MATERIAL

SUPPLY LINE SIZE DRAINAGE LINE SIZE MAIN ISOLATION VALVE STRAINER LOCAL WATER LEVEL INDICATOR OVERFLOW NOZZLE

DESCRIPTION – ACCESSORIES

ANSI Z358.1/AGES-SP-03-001 APPROVED BY: * PULL ROD, PUSH PLATE / FOOT TREADLE FOR EYE WASH ACTIVATION (NOTE 10) 15 MINS NOTE 14 * *

CONNECTIONS

2” (refer to doc. 1-GH5161-04-PID-1005-01) * * REQUIRED REQUIRED REQUIRED TEST

TEST CERTIFICATES AND RELEVANT APPROVALS SHALL BE PROVIDED

MATERIALS

TANK: MEDIUM DENSITY POLYETHYLENE WITH GRP JACKET AND POLYURETHANE INSULATION. PIPING & FITTINGS: BRASS OR STAINLESS STEEL (NON-CORROSIVE)

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. DUST COVERS TO BE PROVIDED TO PROTECT EYEWASH AND RELEASE AUTOMATICALLY WITH WATER PRESSURE
3. EQUIPMENT TO BE EQUIPPED WITH INSULATION, EMERGENCY SIGNS & PICTOGRAMS (IN ARABIC AND ENGHLISH)
4. MATERIAL USED SHALL BE SUITABLE FOR MARINE, HUMID, SALINE ATMOSPHERE WITH AIR-BORNE DUST AND SAND (OUTDOOR), AND POTABLE WATER SERVICE
5. THE COMBINATION EYE BATH WITH SHOWER SHALL BE CAPABLE OF OPERATING THE UNITS SIMULTANEOUSLY
6. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
7. SAFETY SHOWER WITH OVERHEAD WATER TANK SHALL BE PROVIDED
8. COMBINED SAFETY SHOWER / EYEWASH STATION ALONG WITH OVERHEAD TANK SHALL BE PROVIDED WITH SUN SHADE, INSULATION AND CHILLER UNIT OR ALTERNATE OPTION TO PREVENT OVERHEATING BY SOLAR RADIATION. WATER TEMPERATURE SHALL BE MAINTAINED BETWEEN 16 DEG C AND 38 DEG C.
9. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
10. THE VALVES ONCE OPERATED SHALL REMAIN OPEN UNTIL SUCH TIME AS THEY ARE SHUT-OFF MANUALLY
11. COMBINED SAFETY SHOWER / EYEWASH STATION SHALL BE A FREE STANDING, SELF SUPPORTING UNIT OF WHICH THE FRAME SHALL BE PAINTED.
12. FLOW REGULATOR SHALL BE PROVIDED FOR EYEWASH.
13. ALL ELECTRICAL/INSTRUMENTATION EQUIPMENT LOCATED IN PROCESS AREA SHALL BE SUITABLE FOR MINIMUM ZONE 2, GAS GROUP IIB, TEMPERATURE CLASS T3. 14.ANY OPERATION OF THE SAFETY SHOWER / EYEWASH NEED TO REFLECT IN ICSS SYSTEM IN GOP/DC AND OPP
14. SAFETY SHOWER AND EYEWASH REQUIREMENTS SPECIFIED IN ADNOC STANDARD AGES-SP-03-001 TO BE COMPLIED.
15. ZONE 1 CERTIFIED JUNCTION BOX (AS PER AREA CLASSIFICATION) /HOUSING WITH SS 316L MATERIAL WITH SUITABLE GLANDS AND ALL OTHER ACCESSORIES
16. ALL FIELD INSTRUMENT SHALL BE SUITABLE FOR INSTALLATION AND CONTINUOUS OPERATION WITHIN A ZONE 1, GAS GROUP IIB AND INGNITION TEMPERATURE CLASS t3 HAZARDOUS AREA AS PER IEC 60079 AS A MINIMUM

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

2

of

32

Uncontrolled When Printed

SAFETY SHOWER CONTAINING INTEGRAL EYE WASH (AT DC)

APPENDIX 1- A3

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

SHOWER + EYE BATH STATION WITH CHILLER UNIT OUTDOOR NOTE 9

OPERATING CONDITIONS

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE WATER TEMPERATURE OPERATING PRESSURE OF SAFETY SHOWER DESIGN PRESSURE OF SAFETY SHOWER OPERATING PRESSURE OF POTABLE WATER SYSTEM DESIGN PRESSURE OF POTABLE WATER SYSTEM FLOW RATE WATER TANK CAPACITY CHILLER UNIT SELF DRAINING BACTERIOSTATIC ADDITIVE POWER REQUIREMENTS

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND °C BARG

OPERATING AMBIENT (NOTE 7 & 8) * * NOT APPLICABLEL - NOTE 17 NOT APPLICABLEL - NOTE 17

BARG

BARG

BARG 76 LPM FOR SHOWER AND 1,5 LPM FOR EYE WASH 1200 LITER (MINIMUM) YES (NOTE 16) YES YES (VENDOR TO INFORM THE REQUIREMENT) *

STANDARD

ACTUATOR MINIMUM DISCHARGE TIME ALARM WEIGHT FRAME MATERIAL

SUPPLY LINE SIZE DRAINAGE LINE SIZE MAIN ISOLATION VALVE STRAINER LOCAL WATER LEVEL INDICATOR OVERFLOW NOZZLE

DESCRIPTION – ACCESSORIES

ANSI Z358.1/AGES-SP-03-001 APPROVED BY: * PULL ROD, PUSH PLATE / FOOT TREADLE FOR EYE WASH ACTIVATION (NOTE 10) 15 MINS NOTE 14 * *

CONNECTIONS

NOT APPLICABLE - NOTE 17 * * REQUIRED REQUIRED REQUIRED TEST

TEST CERTIFICATES AND RELEVANT APPROVALS SHALL BE PROVIDED

MATERIALS

TANK: MEDIUM DENSITY POLYETHYLENE WITH GRP JACKET AND POLYURETHANE INSULATION.

PIPING & FITTINGS: BRASS OR STAINLESS STEEL (NON-CORROSIVE)

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *

2. DUST COVERS TO BE PROVIDED TO PROTECT EYEWASH AND RELEASE AUTOMATICALLY WITH WATER PRESSURE

3. EQUIPMENT TO BE EQUIPPED WITH INSULATION, EMERGENCY SIGNS & PICTOGRAMS (IN ARABIC AND ENGHLISH)

4. MATERIAL USED SHALL BE SUITABLE FOR MARINE, HUMID, SALINE ATMOSPHERE WITH AIR-BORNE DUST AND SAND (OUTDOOR), AND POTABLE WATER SERVICE

5. THE COMBINATION EYE BATH WITH SHOWER SHALL BE CAPABLE OF OPERATING THE UNITS SIMULTANEOUSLY

6. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH

7. SAFETY SHOWER WITH OVERHEAD WATER TANK SHALL BE PROVIDED

8. COMBINED SAFETY SHOWER / EYEWASH STATION ALONG WITH OVERHEAD TANK SHALL BE PROVIDED WITH SUN SHADE, INSULATION AND CHILLER UNIT OR ALTERNATE OPTION TO PREVENT OVERHEATING BY SOLAR RADIATION. WATER TEMPERATURE SHALL BE MAINTAINED BETWEEN 16 DEG C AND 38 DEG C.

9. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

10. THE VALVES ONCE OPERATED SHALL REMAIN OPEN UNTIL SUCH TIME AS THEY ARE SHUT-OFF MANUALLY

11. COMBINED SAFETY SHOWER / EYEWASH STATION SHALL BE A FREE STANDING, SELF SUPPORTING UNIT OF WHICH THE FRAME SHALL BE PAINTED.

12. FLOW REGULATOR SHALL BE PROVIDED FOR EYEWASH.

13. ALL ELECTRICAL/INSTRUMENTATION EQUIPMENT LOCATED IN PROCESS AREA SHALL BE SUITABLE FOR MINIMUM ZONE 2, GAS GROUP IIB, TEMPERATURE CLASS T3.

14. INDICATION SHALL BE GENERATED IN CONTROL ROOM UPON THE ACTIVATION OF SAFETY SHOWER AND EYEWASH STATION. FLOWSWITCH (FLOW TRANSMITTER SHALL BE PROVIDED BY VENDOR PART OF SAFETY SHOWER FOR REMOTE INDICATION)

15. SAFETY SHOWER AND EYEWASH REQUIREMENTS SPECIFIED IN ADNOC STANDARD AGES-SP-03-001 TO BE COMPLIED.

16. ZONE 1 CERTIFIED JUNCTION BOX (AS PER AREA CLASSIFICATION) /HOUSING WITH SS 316L MATERIAL WITH SUITABLE GLANDS AND ALL OTHER ACCESSORIES

17. THE SAFETY SHOWER WITH INCORPORATED EYES WASH AT DC ARE NOT CONNECTED TO WATER SUPPLY LINE. THEY SHALL BE STANDALONE TYPE. VENDOR TO SPECIFY THE TIME PERIOD FOR REFILLING OF TANK.

18. ALL FIELD INSTRUMENT SHALL BE SUITABLE FOR INSTALLATION AND CONTINUOUS OPERATION WITHIN A ZONE 1, GAS GROUP IIB AND INGNITION TEMPERATURE CLASS t3 HAZARDOUS AREA AS PER IEC 60079 AS A MINIMUM

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

3

of

32

Uncontrolled When Printed

PORTABLE SAFETY SHOWER CONTAINING INTEGRAL EYE WASH (AT DC)

APPENDIX 1- A4

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

SHOWER + EYE BATH STATION WITHOUT CHILLER (to be provided for pigging operation) OUTDOOR NOTE 6

OPERATING CONDITIONS

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE WATER TEMPERATURE OPERATING PRESSURE OF SAFETY SHOWER DESIGN PRESSURE OF SAFETY SHOWER OPERATING PRESSURE OF POTABLE WATER SYSTEM DESIGN PRESSURE OF POTABLE WATER SYSTEM FLOW RATE WATER TANK CAPACITY CHILLER UNIT SELF DRAINING BACTERIOSTATIC ADDITIVE POWER REQUIREMENTS

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND OPERATING AMBIENT °C * BARG * NOT APPLICABLE - NOTE 7 NOT APPLICABLE - NOTE 7

BARG

BARG

BARG 76 LPM FOR SHOWER AND 1,5 LPM FOR EYE WASH 113 liters minimum NO * YES (VENDOR TO INFORM THE REQUIREMENT) NO

STANDARD MINIMUM DISCHARGE TIME ALARM WEIGHT FRAME MATERIAL

SUPPLY LINE SIZE DRAINAGE LINE SIZE MAIN ISOLATION VALVE STRAINER LOCAL WATER LEVEL INDICATOR OVERFLOW NOZZLE

DESCRIPTION – ACCESSORIES

ANSI Z358.1/AGES-SP-03-001 APPROVED BY: * AS PER ANSI Z3585.1 NO * *

CONNECTIONS

NOT APPLICABLE - NOTE 7 * * * * *

TEST

TEST CERTIFICATES AND RELEVANT APPROVALS SHALL BE PROVIDED

MATERIALS

PIPING & FITTINGS: 316 STAINLESS STEEL (NON-COOROSIVE)

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *

2. DUST COVERS TO BE PROVIDED TO PROTECT EYEWASH

3. EQUIPMENT TO BE EQUIPPED WITH INSULATION, EMERGENCY SIGNS & PICTOGRAMS (IN ARABIC AND ENGHLISH)

4. MATERIAL USED SHALL BE SUITABLE FOR MARINE, HUMID, SALINE ATMOSPHERE WITH AIR-BORNE DUST AND SAND (OUTDOOR), AND POTABLE WATER SERVICE

5. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH

6. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

7. THE SAFETY SHOWER WITH INCORPORATED EYES WASH AT DC ARE NOT CONNECTED TO WATER SUPPLY LINE. THEY SHALL BE STANDALONE TYPE. VENDOR TO SPECIFY THE TIME PERIOD FOR REFILLING OF TANK.

8. THE SAFETY SHOWER + EYE WASH STATION SHALL BE PORTABLE WITH WHEELED TYPE

9. ALL FIELD INSTRUMENT SHALL BE SUITABLE FOR INSTALLATION AND CONTINUOUS OPERATION WITHIN A ZONE 1, GAS GROUP IIB AND INGNITION TEMPERATURE CLASS t3 HAZARDOUS AREA AS PER IEC 60079 AS A MINIMUM

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

4

of

32

APPENDIX 1- A5

WIND SOCKS WITH LIGHTS

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

WIND SOCKS WITH LIGHTS OUTDOOR NOTE 5

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

STANDARD

DESCRIPTION WIND SOCK DIMENSIONS

WIND SOCK MATERIAL WIND SOCK COLOUR POLE HEIGHT POLE DIAMETER

POLE MATERIAL

MAXIMUM WIND CONDITION ILLUMINATION POWER RETRACTABLE

DESCRIPTION – ACCESSORIES

                              APPROVED BY: *

TECHNICAL REQUIREMENTS

POLE MOUNTED WINDSOCK. POLE TO HAVE BEARINGS TO ALLOW LONG-2.5 M; THROAT-1 0.5 M DIAMETER; TAIL-0.50.3 M HYPALON/ VINYL NYLON, HIGH CONTRAST & REFLECTIVE COLOR (RESISTANT TO EFFECTS OF WIND AND WEATHER) FLUORESCENT ORANGE 5000 MM 100 MM

316 SS OR APPROVED EQUIVALENT *

75 KNOTS

YES (NOTE 6, 9)

• (FOR ILLUMINATION LAMP) YES MATERIALS

TEST

TEST CERTIFICATES AND RELEVANT APPROVALS SHALL BE PROVIDED

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. ALL MATERIALS SHALL BE SUITABLE FOR OFFSHORE ENVIRONMENT AND EXPOSURE TO DIRECT SUNLIGHT (MAINLY UV RAYS).
3. THEY SHALL BE INSTALLED ON COLLAPSIBLE POLES TO EASE THEIR REPLACEMENT. POLE SHALL HAVE BASE SUITABLE TO BE BOLTED OR WELDED TO THE GRADE
4. WINDSOCK SHALL BE OPEN AT BOTH ENDS.
5. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
6. ILLUMINATION SHALL BE PROVIDED BY VENDOR FOR VISIBILITY DURING NIGHT TIMES.
7. THE TAPER OF THE WINDSOCK FROM THROAT TO THE TRAILING END SHALL BE DESIGNED SO AS TO CAUSE THE WINDSOCK TO FULLY EXTEND WHEN EXPOSED TO A WIND OF 15 KNOTS.
8. WINDSOCK MUST MOVE FREELY ABOUT THE VERTICAL SHAFT IT IS ATTACHED TO AND WHEN SUBJECTED TO WIND OF 3 KNOTS (5.6 KM/H OR 3.5 MPH) OR MORE AND INDICATE THE TRUE WIND DIRECTION WITHIN +/- 5 DEGREES
9. LIGHTING SHOULD BE PROVIDED WITH 1.5 HOURS BATTERY BACK- UP. BATTERY SHALL BE SUITABLE FOR INSTALLATION IN ZONE-1, GAS GROUP IIB, TEMPERATURE CLASS T3, AS A MINIMUM, AS APPLICABLE.
10. WIND SOCK REQUIREMENTS SPECIFIED IN ADNOC STANDARD AGES-SP-03-001 TO BE COMPLIED

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

5

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A6

LIFEBUOYS

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

LIFEBUOYS OUTDOORS/OFFSHORE NOTE 5

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

STANDARD

HSE-OS-ST20/ SOLAS 74/96 APPROVAL BY- EC / SOLAS / MED

DESCRIPTION – ACCESSORIES

GRAB LINES

BUOYANT LIFE LINES REFLECTIVE TAPES MOUNTING BRACKETS SELF IGNITING LIGHTS SELF ACTIVATING SMOKE S UV-RESISTANT MARKING

CABINET WEIGHT BUOYANCY DIMENSION

CONFORMANCE TO SOLAS

YES X

YES X

YES X YES X YES X YES X YES X YES X

YES X

NO

NO

NO NO NO NO NO NO

NO

CABINET SHALL BE WATER PROOF

2.5 KG APPROX 140 – 150N OUTER 720MM / INNER 440MM

TEST

MATERIALS

BRACKET: GALVANIZED STEEEL COLOR: INTERNATIONAL ORANGE (AS PER COMPANY’S COATING SPECIFICATION, SP-1170) BUOY : POLYURETHANE FOAM (HARD PU) SHELL FILLED WITH HARD POLYURETHANE (*) VISIBILITY FEATURES: ATTACHED WITH FOUR REFLECTIVE TAPE SURROUNDED BY GRAB ROPES

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. BRACKETS SHALL BE PROVIDED FOR LIFEBUOYS. BRACKETS SHALL BE OF GALVANISED STELL CONSTRUCTION AND SUITABLE FOR HANDRAIL MOUNTING
4. NAME OF THE LOCATION SHALL BE MARKED ON THE LIFEBUOYS
5. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
6. SELF-IGNITING LIGHTS SHALL MEET THE LSA CODE CL 2.1.2 REQUIREMENTS BEING DESIGNED THAT THEY CANNOT BE EXTINGUISHED IN WATER, WHITE IN COLOUR AND LUMINOUS INTENSITY OF 2CD.
7. LIFEBUOYS SHOULD BE STORED IN A DEDICATED CLEARLY MARKED LIFEBUOY HOUSING TO PROTECT IT FROM THE ELEMENTS
8. LIFE BUOY REQUIREMENTS SPECIFIED IN ADNOC HSE STANDARD HSE-OS-ST2O AND AGES-SP-03-001 TO BE COMPLIED.

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

6

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

3 MIN 58 MAX

°C DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND 6 PERSON CAPACITY DESCRIPTION – ACCESSORIES

BLACK BODY TEMPERATURE : 85

SOLAS APPROVAL BY- SOLAS LSA-CODE/EC DIRECTIVE 96/98/EC/MED LENGHT*

HEIGHT*

WIDTH*

YES X

NO

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

SELF INFLATABLE/THROW OVERBOARD TYPE (NOTE 10) OUTDOORS/OFFSHORE NOTE 8

OPERATING CONDITIONS

APPENDIX 1- A7 LIFE RAFT

AMBIENT TEMPERATURE HUMIDITY ATMOSPHERE LIFE RAFT CAPACITY

STANDARD DIMENSION (m) SOLAS PACK A WITH 6 PERSON CAPACIT DAVIT CRANE

HOLDING CRADLE PROTECTIVE COVER CONTAINER MARKING HYDROSTATIC RELEASE HAND RELEASE WEBBING/ BOARDING RAMP

YES YES X YES X YES X YES X YES X YES X YES X

LINE PAINTER SART RADAR REFLECTOR PADDLES SPONGES BAILER BELLOWS LEAK STOPPAGE

SAFETY KNIFE

SEA ANCHOR FIRST AID KIT REPAIR KIT

COLOUR

NOTE 4

X

NO NO NO NO NO NO NO NO DESCRIPTION – ACCESSORIES (NOTE 11) NO NO NO NO NO NO NO NO NO NO NO NO

YES X YES X YES X YES X YES X YES X YES X YES X YES X YES X YES X YES X CONTAINER: WHITE LIFE RAFT: ORANGE

BUOYANCY TESTING ACCORDANCE WITH I.M.O. WATER TIGHTNESS TEST IN ACCORDANCE WITH IMO. PRESSURE TEST *

TEST

MATERIALS

CONTAINER: * GRP MATERIAL OF CONSTRUCTION OF THE LIFE RAFT PACKAGE SHALL BE SUITABLE FOR OFFSHORE MARINE CONDITION

REMARKS

1. • VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. MATERIAL OF CONSTRUCTION OF THE LIFE RAFT PACKAGE SHALL BE SUITABLE FOR OFFSHORE MARINE CONDITION.
4. MARKING SHALL BE PROVIDED FOR THE LIFE RAFT COMPLIANT TO SOLAS REQUIREMENT (IN ENGLISH AND ARABIC)
5. THE VENDOR SHALL SPECIFY THE MAXIMUM WEIGHT/LOAD WHICH THE LIFE RAFT CAN WITHSTAND. THE VENDOR DECLARATION SHALL MEET ALL THE REQUIREMENT OF APPLICABLE SAFETY OF LIFE AT SEA CODES SOLAS WITH NO EXCEPTION.
6. ALL OPERATING NOTICES FOR LIFE-RAFT SHALL BE WRITTEN IN ARABIC AND ENGLISH LANGUAGES. THIS OPERATING NOTICE SHALL BE DISPLAYED NEAR LIFE RAFT STATION.HENCE THE MATERIAL OF CONSTRUCTION OF THIS NOTICE BOARD AND FIXING ACCESSORIES SHALL BE SUITABLE FOR OFFSHORE MARINE ENVIRONMENT AND SHALL HAVE PHOTO –LUMINESCENT DISPLAY.
7. LIFE RAFT ENTRY SHALL BE SUCH THAT PERSONNEL COULD EMBARK WEARING BREATHING APPARATUS. LIFE RAFT SHALL HAVE TWO ENTRANCES AND EACH ENTRANCE FITTED WITH BOARDING LADDER.
8. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
9. A MARINE RESISTANT WHITE COLOURED GLASS REINFORCES PLASTIC CONTAINER TO BE PROVIDED FOR STORAGE.
10. LIFE RAFT REQUIREMENTS SPECIFIED IN ADNOC STANDARD AGES-SP-03-001 TO BE COMPLIED.
11. EACH LIFE RAFT SHALL BE PROVIDED WITH A SOLAS PACK A EMERGENCY PACK

1-CF0000-40-SPE-0032-00

Contractor Document Number

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

Sheet

7

of

32

REV

B3

DOCUMENT CLASS – 1

Uncontrolled When Printed

APPENDIX 1- A8

LIFE JACKET

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

SELF INFLATABLE OUTDOOR/OFFSHORE NOTE 6

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

OPERATING CONDITIONS

HUMIDITY ATMOSPHERE

STYLE

STANDARD

DIMENSION (m) BUOYANCY WEIGHT

SIZE

WHISTLE & LANYARD

REFLECTIVE STRIPS LIFTING BRACKET

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND ERGONOMIC SHAPE FOR COMFORT & FREEDOM OF MOVEMENT. TWIN CHAMBERS FOR DOUBLE SECURITY AND EACH CHAMBER CAN BE INFLATED VIA ITS INDIVIDUAL

DESCRIPTION – ACCESSORIES

AGES-SP-03-001 SOLAS testing standards MSC 201 (81), MSC 207 (81), MSC 200 (80), MSC 226 (82), MSC 323 (89) ISO 12402-7/BS EN ISO 12402-7

WIDTH*

HEIGHT*

APPROVAL BY:

LENGTH* *150 N

ADULT

YES X

YES X YES X

NO

NO NO

CLOSURE/FASTENING DETAILS

YES X

NO

THE INFLATABLE CHAMBER IS MADE OF HIGH VISIBILITY YELLOW FABRIC, IS FOLDED INTO A VALISE WITH VELCRO CLOSURE AND ITS INFLATION TUBE INCORPORATES THE NEW LALIZAS RED PRESSURE RELIEF VALVES (20611, CERTIFIED PER ISO 12402-7).

LIFE JACKET LIGHT (WITH BATTERY)

YES X

NO

SUITABLE TO WITHSTAND A JUMP INTO WATER FROM 4.5 M, WHICH COMES ON AUTOMATICALLY ON CONTACT WITH WATER, AND WHICH CAN BE RELOCATED BY THE WEARER TO AN OPTIMUM POSITION

STORAGE CABINET

YES X

NO

Conformance to SOLAS

LIFE JACKET

TEST

MATERIALS

SOFT PVC (RAW MATERIALS TESTED ACCORDING TO: ISO:12402-7, ISO:12402-8) - COLOUR: YELLOW/RED

STORAGE CONTAINER

NOTE 4 COLOUR:*

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. SELF STANDING LOCKABLE CONTAINERS OF UV RESISTANT, WEATHER PROOF GRP CONSTRUCTION WITH HEAVY DUTY HINGES SHALL BE SUPPLIED TO STORE LIFE JACKETS.
3. CONTAINER SHALL CONTAIN NO. 6 OF LIFE JACKET STORED.
4. LIFE JACKET CONTAINER SHALL BE STENCILED WITH “LIFE JACKETS”. IP56 RATING SHALL BE REQUIRED.
5. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
6. LIFE JACKET REQUIREMENTS SPECIFIED IN ADNOC HSE STANDARD HSE-OS-ST2O AND AGES-SP-03-001 TO BE COMPLIED.
7. A SUITABLE LIFEJACKET SECURING SYSTEM (SUCH AS CROTCH OR THIGH STRAPS) WHICH PREVENTS THE LIFEJACKET RISING UP.
8. LIFEJACKET CHAMBER CONFIGURATION/BUOYANCY SUCH AS TO ENSURE THE RIGHTING OF AN UNCONSCIOUS PERSON WEARING ANY CLOTHING EXPECTED FOR EVACUATION.
9. NECK SUPPORT AND BUOYANCY SUCH AS TO ENSURE SUFFICIENT MOUTH-TO-WATER DISTANCE (120MM) FOR AN UNCONSCIOUS PERSON WEARING THE INSTALLATION IMMERSION SUIT.

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

8

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

EMERGENCY ESCAPE BREATHING APPARATUS (EEBA) - MASK TYPE

APPENDIX 1- A9

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

MASK TYPE EEBA INDOOR/OUTDOOR OFFSHORE NOTE 6

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

OPERATING CONDITIONS

HUMIDITY ATMOSPHERE

DESIGN STANDARD DURATION, AIR SUPPLY AIR QUALITY FLOW RATE

CYLINDER PRESSURE WEIGHT BREATHING TUBE REGULATOR

MASK TYPE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

DESCRIPTION – ACCESSORIES

EN 402:2005 20 MIN D AS PER EN 12021 35 L/MIN

• 200 BAR (CAPABLE TO BE CARGED UP TO 300 BARG)
• VALVE ARRANGEMENT TO PREVENT EXCESS FLOW DURING ACCIDENTAL KNOCKOFF.
• BOTTLE SUPPORTED ON THE BACK OF OPERATOR
• SEPARATE QUICK FIXED LINE FOR FILLING CONNECTION 3.4 KG EMPTY/4.2 KG FULL OR LESS (FIBER GLASS AIR CYLINDERS TYPE) STANDARD ADJ. FLOW BALANCED PISTON TYPE
• PANORAMA FULL FACE MASK COMPATIBLE WITH SPEECH DIAPHRAGM ASSEMBLY (NOTE 3)
• QUICK DONNING TIME
• HIGH PROTECTION FACTOR (FOR H2S 35,000 PPM OR HIGHER).
• EEBA WITH HOOD TYPE RAPID SELF-ADJUSTMENT MASK
• AIR LOOP QUICK FIXED AIRLINE CONNECTION.
• AUTOMATIC POSITIVE PRESSURE ACTIVATION
• ALLOW FOR USE OF SPECTACLES / PRESCRIPTION LENSES
• NATURAL FIELD OF VISION, WITH ANTI-FOG AND ANTI-SCRATCH
• COMPATIBLE WITH SIGNIFICANT FACIAL HAIR SUBJECT TO SUCCESSFUL QUALITATIVE FIT TESTING/ TYPE. CAMLOCK OR EQUIVALENT.

AIRFLOW TO HOOD

CARRYNG CASE

DEMAND FLOW TO FACE MASK THE CARRING BAS IS MADE OF PVC COATED NYLON. THOS IS COLORED FOR HIGH VISIBILITY AND IN BOTH FLAME RESISTANT AND CHEMICAL SPLASH RESISTANT. THERE IS AN ANTISTATIC OPTION FOR WORKING IN POTENTIALLY EXPLOSIVE ATMSPHERE AND THIS IS MADE OF POLYURETHANEù. THE BAG CAN BE WORN ACROSS THE CHEST, AS A BANDOLLER OR WORN WITH AN OPTIONAL WAIST BELL

CABINET

GREEN COLOUR CABINET CONTAINING EACH 10 EEBA SETS SHALL BE PROVIDED. THESE SHALL BE REINFORCED FLAME RESISTANT GLASS FIBRE CABINET FITTED HINGED FRONT OPENING DOOR WITH ACRYLIC CLEAR VISION. “ESCAPE BREATHING APPRATUS” MARKING IN ARABIC AND ENGLISH.

OPERATING TEMPERATURE RANGE ADDITIONAL REQUIREMENT

15°C TO +60°C

AUTOMATIC ACTIVATION

TESTING IN ACCORDANCE WITH EN 402:2005/SOLAS CHAPTER II-2 CE MARKED IN ACCORDANCE WITH EN402:2005 MED SHIPWHELL APPROVED AS/NZ1716 CYLINDER

COMPOSITE

TEST

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. POSTIVE PRESSURE TYPE,WIDE VISION , NON FOGGING FACE MASK WITH LENS AND NOSE CUP. PANORAMA FULL FACE MASK COMPATIBLE WITH SPEECH DIAPHRAGM ASSEMBLY.
4. REGULATOR SHALL BE ADJUSTABLE FLOW BALANCED PISTON TYPE.
5. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
6. EEBA REQUIREMENTS SPECIFIED IN ADNOC HSE STANDARD HSE-OS-ST20 TO BE COMPLIED.

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

9

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

AMBIENT TEMPERATURE

HUMIDITY ATMOSPHERE

DESIGN STANDARD DURATION, AIR SUPPLY AIR QUALITY FLOW RATE SYSTEM PRESSURE WEIGHT

CYLINDER CONNECTION AIRLINE HARNESS TYPE

LIGHT WEIGHT SELF CONTAINED BREATHING APPARATUS (SCBA)

APPENDIX 1- A10

OPEN CIRCUIT, POSITIVE PRESSURE , TYPE 2 INDOOR/OUTDOOR NOTE 5

OPERATING CONDITIONS

°C

3

MIN

58

MAX

BLACK BODY TEMPERATURE : 85

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

DESCRIPTION – ACCESSORIES

EN137: 2006 TYPE 2, SOLAS, MED,IMO, MSC, ISO 23261-3 45 MIN D AS PER EN 12021 CONSTANT (LUNG DEMAND VALVE) 300 BAR CYLINDER LIGHTWEIGHT, 5 - 7.5 KG WITH VALVE

HANSEN CONNECTION TO CASCADE SYSTEM

STANDARD WITH CHEST STRAP

CYLINDER CRADLE /MOUNTING TYPE LUMBAR TYPE REGULATOR TYPE REGULATOR HOSE TYPE HOOD MATERIAL SIZE

FABRIC BAND ADJUSTABLE SWIVELING LUMBAR SOLID COVER - LEFT/RIGHT SHOULDER REGULATOR HOSE TYPE PANORAMA FULL FACE MASK COMPATIBLE WITH SPEECH DIAPHRAGM ASSEMBLY (NOTE 3) HEIGHT 600-700 MM X LENGTH 250-300 MM X BREADTH 200-250 MM

WEIGHT

COLOR CYLINDER FREE CAPACITY CYLINDER WATER CAPACITY AIRFLOW TO HOOD

WEIGHT W CYLINDER (MAX KG) = 10.5 KG WEIGHT W/O CYLINDER (MAX KG) = 3 KG STANDARD AT LEAST 1200 L 6-7 L DEMAND FLOW TO FACE MASK

REDUCER PRESSURE AND FLOW

.5 BARS; >1200 L/MIN

OPERATING TEMPERATURE RANGE

15°C TO +60°C

CYLINDER FEATURE

• LIGHTWEIGHT CARBON COMPOSITE CYLINDERS DESIGNED FOR CHARGING UP TO 300 BARG.
• VALVE ARRANGEMENT TO PREVENT EXCESS FLOW DURING ACCIDENTAL KNOCKOFF.
• AUTOMATIC SWITCH-OVER VALVE FROM SUPPLIED AIR TO CYLINDER
• SEPARATE QUICK FIXED LINE FOR FILLING CONNECTION
• SHOCK-PROOF BOX WITH PRESSURE GAGE INSPECTION WINDOW
• CYLINDER PROTECTIVE SLEEVE

CYLINDER PRESSURE WARNING

WHISTLE/ALARM ACTIVATION PRESSURE = 55 ± 5 BAR WHISTLE SOUND LEVEL (DBA) = >90 FOR 60 SEC INTERMITTENT SOUND AND 15 SEC FOR CONTINUOUS 25

FACE MASK

BACK PLATE /HARNESS

-CERTIFIED WORK-PLACE STUDY PROTECTION FACTOR OF AT LEAST 350,000PPM (SUITABLE FOR 35% H2S ENVIRONMENT.

• POSITIVE PRESSURE TYPE.

• WHERE SEPARATE COMPONENTS ARE IN MORE THAN ONE SIZE, THE SAME SIZE UNITS ARE TO BE EASILY IDENTIFIABLE (E.G. THROUGH COLOUR CODING)

• NATURAL FIELD OF VISION, WITH ANTI-FOG AND ANTI-SCRATCH.

• MUST PROVIDE CLEAR SPEECH AND AUDIBILITY WHILE USING RADIO UNITS (INTEGRATED APPROACH PREFERRED, OR DEMONSTRATION OF ACCEPTABLE CLARITY).

• DESIGNED TO SUPPORT/INTEGRATE WITH OTHER PPE (E.G. PROTECTIVE HELMET) BUILT IN COMMUNICATION OUTPUT AND CONNECTION FOR TALKY WALKY (COMPATIBLE TYPE).

• ALLOW FOR USE OF SPECTACLES / PRESCRIPTION LENSES.

• COMPATIBLE WITH SIGNIFICANT FACIAL HAIR SUBJECT TO SUCCESSFUL QUALITATIVE FIT TESTING

• PANORAMIC FULL FACE MASK AND AIR LOOP QUICK FIXED AIRLINE CONNECTION.

• ERGONOMIC AND FULLY ADJUSTABLE FOR FIT AND COMFORT

• MATERIAL SUITABLE FOR USE IN AN AREA WHERE THERE IS A POSSIBILITY OF HIGH H2S CONCENTRATION AND HARSH DESERT ENVIRONMENT

• LIGHT REFLECTING STRIPS

• DESIGN PROVIDES PROTECTION FOR HOSES DRAGER OR EQUIVALENT

COMPLIANCE WITH EN 136:1998 AND EN 137:2006 COMPLIANCE WITH ISO 23269-2 (2011) CALLED BY ISO 23269-3

TEST

MATERIALS

CYLINDER

CABINET

CARBON COMPOSITE OR STEEL ALLOY TYPE

REINFORCED FLAME RESISTANT GLASS FIBRE CABINET FITTED HINGED FRONT OPENING DOOR WITH ACRYLIC CLEAR VISION.

MOUNTING

MARKINGS DIMENSION

SUITABLE FOR BULKHEAD FIXING ABOVE DECK. OPTION FOR MOUNTING ON HANDRAILING/COLUMN/POLE TO BE INCLUDED.

BREATHING APPARATUS” IN ARABIC AND ENGLISH. *

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. POSTIVE-PRESSURE TYPE, WIDE VISION, NON FOGGING FACE MASK. PANORAMA FULL FACE MASK COMPATIBLE WITH SPEECH DIAPHRAGM ASSEMBLY.
4. DEMAND VALVES, HOSES, QUICK CONNECTION FITTINGS AND OTHER COMPONENTS FOR A SAFE AND EFFICIENT USE
5. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
6. SCBA SHALL BE PROVIDED WITH AUTOMATIC SWITCH OVER VALVE TO SWITCH BETWEEN BREATHING AIR LINE AND CYLINDER. CONNECTION SHALL BE SUITABLE TO CONNECT SCBA TO CASCADE AIR SYSTEM
7. CYLINDER PRESSURE WARNING (ALARM/WHISTLE) SHALL BE PROVIDED AS PER ADNOC HSE STANDARD HSE-OS-ST2O.
8. SCBA REQUIREMENTS SPECIFIED IN ADNOC HSE STANDARD HSE-OS-ST2O TO BE COMPLIED WHERE NOT SPECIFIED IN THIS DATASHEET

DOCUMENT CLASS – 1

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

Sheet

10

of

32

REV

B3

APPENDIX 1- A11

HELICOPTER CRASH EQUIPMENT CABINET

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

DECK MOUNTED/SELF STANDING OUTDOOR/OFFSHORE NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

OPERATING CONDITIONS

HUMIDITY ATMOSPHERE

STANDARD DIMENSION (m) DOOR CLOSING SHELVES

SUPPORT

ROOF VENTILATION

AIR CRAFT RESCUE AXE ADJUSTABLE WRENCH PAIR BOLT CROPPERS LARGE CROWBAR TWO-PIECE LADDER PLIER, SIDE-CUTTING (TIN- SNIPS)

HACKSAW C/W SIX SPARE BLADES

RESCUE GRAB HOOK SEALED TORCH LIGHT (APPROVED FOR HAZARDOUS AREA) QUICK RELEASE HARNESS LIFELINE FIRE BLANKET FULL BODY HARNESS POWER CUTTING TOOL SCREW DRIVERS ASSORTED SCREW HARNESS KNIVES X 2

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

DESCRIPTION – ACCESSORIES

•                                         APPROVAL BY *
  

LENGTH* DOUBLE DOOR LOCK

WIDTH*

HEIGHT*

ITEMS STORED

YES X

YES X

YES X YES X

YES X YES X YES X YES X YES X

YES X

YES X

YES X

YES X

YES X YES X YES X YES X YES X YES X YES X YES X

NO

NO

NO NO

NO NO NO NO NO

NO

NO

NO

NO

NO NO NO NO NO NO NO NO

TEST CERTIFICATES TO BE PROVIDED BY VENDOR

CONTAINER: * (NOTE 4) COLOUR: GREEN

TEST

MATERIALS

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
4. LOCKABLE STORAGE CABINETS OF UV RESISTANT, WEATHER PROOF, GRP CONSTRUCTION WITH HEAVY DUTY HINGES SHALL BE PROVIDED.

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

11

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A12

CHEMICAL KIT

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

CHEMICAL KIT OUTDOOR NOTE 5

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

DIMENSION (m)

CONTENT

DESCRIPTION – ACCESSORIES

LENGHT* 2 NOS. CHEMICAL RESISTANT GLOVE 2 NOS. OF GOGGLES (TRANSPARENT GLASS) 2 NOS. OF CHEMICAL SUIT

WIDTH*

HEIGHT*

CABINET TYPE

CABINET MATERIAL

LOCKABLE, GRP CABINETS, SUITABLE FOR WALL, HANDRAIL & DECK MOUNTING, WITH DRAIN FIRE RETARDANT WITH STAINLESS STEEL FITTING

CABINET PROTECTION FULLY ENCLOSED AND PROTECTED TO IP53 WITH UV RESISTANT GRP / EQUIVALENT

CABINET COLOR & MARKING

GREEN COLOUR. CABINET SHALL BE STENCILED WITH “CHEMICAL HANDLING KIT” IN ARABIC & ENGLISH

COMPLYING TO EN TESTING & STANDARD. CERTIFICATE OF COMPLIANCE REQUIRED

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. CABINET SHALL HAVE A PERMANENTELLY FIXED AND DURABLE NAMEPLATE LISTING THE CABINET CONTENT IN ARABIC AND ENGLISH
3. CABINET SHALL HAVE AN ARRANGEMENT FOR WALL MOUNTING/DESK & HANDRAIL MOUNTING 4, SAFETY SIGN SHALL BE SUPPLIED ON 4MM PVC PLATE TO THE FIXED ON CABINET 5, REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

12

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A13

FIRST AID KIT

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

CABINET/WALL/HANDRAIL MOUNTED INDOOR/OUTDOOR NOTE 5

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

DESCRIPTION – ACCESSORIES

STANDARD

AGES-SP-03-001/ANSI Z 308.1 / OSHA / Marine 400 (NOTE 4) APPROVED BY: USGC

DIMENSION (m)

DEPTH*

150 WIDTH*

300

HEIGHT*

300

ACCESSORIES

AS A MINIMUM SHOULD INCLUDE THE FOLLOWING:

1. EYEWASH BOTTLES – 2 NOS

2. WASHPROOF ASSORTED 4 SIZES – BOX 20 - 40 NOS

3. NON-WOVEN ADHESIVE ISLAND DRESSING – 10 NOS

4. WOUND CLOSURES 3 X 75 MM X 5 / CARD. 1 CARD/POUCH - 20 NOS

5. MEDIUM DRESSING - 1 NO

6. EYE PADS - 2 NOS

7. LOW- ADHERENT PADS - 5NOS

8. NON-WOVEN TRIANGULAR BANDAGE - 1NO

9. NON-STERILE COTTON WOOL - 1 PACK

10. ELASTIC COTTON CREPE BANDAGE - 1NO

11. CLEAR PLASTIC TAPE 2.5 CM X 5 M BOX 12

12. SALINE CLEANSING WIPES BULK - EACH – 4 NOS

13. INSTANT ICE PACKS - 1 NO

14. AMMONIA INHALANTS- 2 NOS

15. ANTISEPTIC CREAM – 1 NO

16. TUFFCUT SCISSORS 7.5” X 190MM – 1 NO EACH

17. STAINLESS STEEL TWEEZERS– 1 NO

18. 2 NOS. VINYL GLOVES POWDERED

19. YELLOW SELF SEAL DISPOSAL BAG 200 X 310 MM - EACH - 2NOS

20. FIRST AID MANUAL (A4) COMPLETE WITH THE LATEST GUIDELINES - EACH

TEST CERTIFICATES AND RELEVANT APPROVALS SHALL BE PROVIDED

MATERIALS

CABINET: (FIRE RETARDANT WITH STAINLESS STEEL FITTINGS) - COLOUR: GREEN FULLY ENCLOSED AND PROTECTED TO IP53 WITH UV RESISTANT GRP

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. COLOUR OF THE BOX SHALL BE GREEN WITH “FIRST AID” MARKED IN ENGLISH AND ARABIC. A GREEN CRESENT SHALL BE PROVIDED ON THE FIRST AID BOX
4. FIRST AID KIT SHALL BE COMPLIANCE WITH ANSI Z308.1 TYPE III MOBILE OUTDOOR FIRSTAID KIT.
5. INDOOR FAK TO BE PROVIDED BY BUILDING SUBCONTRACTOR. OUTDOOR FAK TO BE PROVIDED BY OTHER VENDOR
6. FIRST AID KIT REQUIREMENTS SPECIFIED IN ADNOC STANDARD AGES-SP-03-001 TO BE COMPLIED

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

13

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A14

ELECTRICAL SAFETY KIT

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

WALL MOUNTED INDOOR/ONSHORE/OFFSHORE NOTE 4

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

OPERATING CONDITIONS

HUMIDITY ATMOSPHERE

STANDARD*

DOOR CLOSING SHELVES SUPPORT ROOF VENTILATION

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

DESCRIPTION – ACCESSORIES

APPROVED BY: *

STORAGE CABINET DETAILS

DOUBLE DOOR LOCK YES BASE SLOPING NATURAL

ITEMS STORED AS MINIMUM

1. RUBBER BOOTS – 2 PAIRS
2. RUBBER HAND GLOVES (Max. Voltage 33kV)– 2 PAIRS
3. MOBILE EARTHING KIT - No. 1
4. RESCUE STICK - No. 1
5. VOLTAGE INDICATOR LOCKED ON STICK END - No. 1
6. LIVE LINE TESTER - No. 1
7. RUBBER MAT - No. 1
8. INSULATED CABLE CUTTER - No. 1
9. INSTRUCTION MANUAL - No. 1
10. AUTOMATED EXTERNAL DEFIBRILLATOR (AED) - No. 1
11. MINIMUM PAIR OF ARC FLASH SIUT (2 PIECES TYPE) WITH HELMET MOUNTED FACE-SHIELD SUITABLE TO THE HIGHEST ARC FLASHING RATING OF ELECTRICAL SWITHCGEARS IN THE ROOM
12. RUBBER HAND-GLOVES TESTING MANULA-PUMP
13. EQUIPMENT TAG NO. PLATE
14. SAFETY TORCH
15. CABINET SHALL BE LABELLED EXTERNALLY WITH “ELECTRICAL SAFETY KIT” ON DELF-ILLUMINATED MATERIAL.

MOUNTING CABINET CABINET COLOUR

WALL MOUNTING CAPABILITIES WITH HANDLE AND BRACKET. GRP WITH HINGED FRONT OPENING DOOR GREEN

TEST CERTIFICATES TO BE PROVIDED BY VENDOR

TEST

MATERIALS

CABINET: GREEN - (FIRE RETARDANT WITH STAINLESS STEEL FITTINGS)

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. THE RATING OF THE ELECTRICAL SAFETY EQUIPMENT SHALL BE SUITABLE FOR THE EQUIPMENT WITH THE HIGHEST VOLTAGE RATING
4. TO BE PROVIDED BY BUILDING SUBCONTRACTOR
5. EQUIPMENT STORED IN ELECTRICAL SAFETY KIT SHALL COMPLY WITH REQUIREMENTS SPECIFIED IN ADNOC HSE STANDARD HSE- OS-ST20 AS APPLICABLE.
6. CABINET SHALL HAVE INTERNAL POCKET ON DOOR FOR RECORD CARD/MANUAL/INSTRUCTION

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

14

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A15

PORTABLE EYEWASH STATION

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

SELF CONTAINED EYE WASH STATION INDOOR NOTE 5

OPERATING CONDITIONS

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

STANDARD

ANSI Z358.1/AGES-SP-03-001 APPROVED BY: *

DESCRIPTION – ACCESSORIES

MODEL MANUFACTURER MATERIAL

EYEWASH FLOWRATE OPERATION

DESCRIPTION

ACCESSORIES

ADDITIVES

TECHNICAL REQUIREMENTS

• (HIGH DENSITY POLYETHYLENE)

MINIMUM 1,5 LPM FOR 15 MINUTES AS PER ANSI Z358.1 STANDARD

PULL DOWN MANIFOLD FOR OPERATION SELF CONTAINED PORTABLE EYEWASH PROVIDED WITH WATER DISPOSAL CART WALL MOUNTING BRACKETS/HOOKS, SAFETY SIGNS AND OPERATING INSTRUCTIONS IN BOTH ARABIC AND ENGLISH WATER TREATMENT ADDITIVE TO PREVENT GROWTH OF HARMFUL ORGANISM IN EYEWASH WATER *

TEST CERTIFICATES AND RELEVANT APPROVALS SHALL BE PROVIDED

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. OPERATING SIGN AND INSTRUCTION SHALL BE IN ENGLISH/ARABIC LANGUAGE.
3. WALL MOUNTING BRACKET FOR THE INSTALLATION OF EYE WASH UNIT WILL BE PROVIDED.
4. FLUID DISPOSAL CART SHALL BE PROVIDED TO COLLECT THE DRAINED FLUID.
5. TO BE PROVIDED BY BUILDING SUBCONTRACTOR
6. LABELLED “EYE WASH STATION” ON SELF-ILLUMINATED PLATE AND VISIBLE FROM DISTANCE WITHIN ROOM

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

15

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A16

STRETCHER

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

COLLAPSIBLE INDOOR/OUTDOORS/ONSHORE/OFFSHORE NOTE 6

OPERATING CONDITIONS

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

DESCRIPTION – ACCESSORIES

DIMENSION (m) FOUR INTEGRAL SIDE CARRYING HANDLES TO BE PROVIDED ALLOWING TWO RESCUERS TO CARRY THE CASUALTY

LENGHT*

HEIGHT*

WIDTH*

SLING POINTS PERSONNEL SECURING STRAPS WASHABLE BED FOAM MATRESS PADDED HEAD REST PADDED LEG REST PILLOW BLANKET

CARRYING HANDLE

MOUNTING BRACKETS STORAGE PROVISION CABINET FOR STRETCHER

PLASTIC COVER MARKING

YES X

YES X

YES X YES X YES X YES X YES X YES X

YES X

YES X

YES X

YES X YES X

NO

NO

NO NO NO NO NO NO

NO

NO

NO

NO NO

TEST

TEST CERTIFICATES AND RELEVANT APPROVALS SHALL BE PROVIDED

MATERIALS ALUMINUM FRAMED COLLAPSIBLE TYPE STRETCHER SHALL BE PROVIDED. ALL MATERIAL SHALL BE SUITABLE FOR MARINE ENVIROMENT. COLOUR: GREEN

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. STRETCHER SHALL HAVE NEOPRENE COATED NYLON BOTTOM AND SHALL BE EASILY WASHABLE.
4. FOUR INTEGRAL SIDE CARRYING HANDLES TO BE PROVIDED ALLOWING TWO RESCUERS TO CARRY THE CASUALTY.
5. MANUFACTURER’S TEST CERTIFICATES/COMPLIANCE CERTIFICATE SHALL BE FURNISHED .
6. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT 7.TO BE COMAPTIBLE FOR HELICOPTER USAGE.

DOCUMENT CLASS – 1

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

16

of

32

Uncontrolled When Printed

APPENDIX 1- A17

FIRE BLANKET

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

FIRE BLANKET INDOOR/ONSHORE/OFFSHORE NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

BS EN1869 APPROVAL BY: °

DESCRIPTION – ACCESSORIES

STANDARD SIZE SUPPORT COLOUR

6’ X 4’ * * MANUFACTURER STANDARD

FIRE BLANKET MADE UP OF TEXTURED WOVEN GLASS FIBRE MATERIAL TESTED TO BS 476 PART 4 & 7 FIRE BLANKET MUST BE CERTIFIED “ASBESTOS FREE

MATERIALS

TEST CERTIFICATES AND RELEVENT APPROVAL SHALL BE PROVIDED

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

17

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A18

FACE SHIELD MASK

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

FACE-SHIELD, SAFETY, INDUSTRIAL (HELMET MOUNTED FACE SHIELD) OUTDOOR NOTE 3

OPERATING CONDITIONS

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

STANDARD

APPLICATION

ANSI Z87.1-2010, HSE-OS-ST20,

DESCRIPTION – ACCESSORIES

HIGH VELOCITY IMPACT AGAINST FLYING OBJECTS

• FLUID SPLASH
• CHEMICAL SPLASH
• WELDING SPLASH

STYLE

MATERIAL VISOR

FIELD OF VISION

HELMET MOUNTED USING UNIVERSAL VISOR & SLOT ADAPTER

• FLAT POLYCARBONATE
• FACE SHIELD: 0.040 INCHES (THICKNESS)
• DIMENSIONS : 8” X 15.5” MINIMUM 160°

COMPLYING TO EN TESTING & STANDARD. CERTIFICATE OF COMPLIANCE REQUIRED

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. Embossed with details such as Brand Name, Article Number & Standards Compliance
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

18

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A19

WHEELED AIR LOOP TROLLEYS

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

WHEELED AIR LOOP TROLLEYS OUTDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

Air Pack 4 Composite Cylinder Capacity-9ltr, Cylinder Pressure-300bar, with 2 quick connection high pressure airlines 2 X 25 Meters

DESCRIPTION – ACCESSORIES

TEST CERTIFICATES AND RELEVENT APPROVAL SHALL BE PROVIDED

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

19

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A20

HEAT STRESS MONITOR

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

HEAT STRESS MONITOR OUTDOOR/INDORR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

-Heat Stress Index measures how hot it feels when humidity is combined with temperature, air movement, and radiant heat.

• In/Out Function displays the WBGT value with or without direct sun exposure.
• Auto Power Off with override, complete with two AAA batteries
• Selectable units of °F and °C, intrinsically safe type. Built-in RS-232 interface with optional Windows® compatible software

DESCRIPTION – ACCESSORIES

TEST CERTIFICATES AND RELEVENT APPROVAL SHALL BE PROVIDED

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

20

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A21

HEAT STRESS MONITOR

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

HEAT STRESS MONITOR OUTDOOR/INDORR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

DESCRIPTION – ACCESSORIES

Suitable for measuring noise in the field of industrial, health, safety and environmental monitoring. Intrinsically safe type.

• Automatic range: 30 … 130 dB
• Manual range: 30 … 80 / 50 … 100 / 80 … 130 dB
• Resolution: 0.1 dB
• Accuracy: ±1.4 dB
• Memory capacity: 32700 values
• Include software for LEQ calculation, with a logger function.

TEST CERTIFICATES AND RELEVENT APPROVAL SHALL BE PROVIDED

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

21

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A22

SAFETY GLOVES

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

SAFETY GLOVES OUTDOOR/INDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

AS PER HSE-OS-ST20 - SECTION 3.1 - GLOVES, IMPACT, PROTECTION, INDUSTRIAL SPECIFICATIONS

DESCRIPTION – ACCESSORIES

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT 4, VENDORTO PREPARE DETAILED DATA SHEET

REMARKS

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

22

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A23

HAND HELD MEGAPHONE

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

HAND HELD MEGAPHONE OUTDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

VENDOR STANDARD

DESCRIPTION – ACCESSORIES

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT 4, VENDORTO PREPARE DETAILED DATA SHEET

REMARKS

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

23

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A24

RECHARGEABLE TORCHES

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

RECHARGEABLE TORCHES OUTDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

VENDOR STANDARD TORCHES SHALL BE SUITABLE FOR HAZARDOUS AREA ZONE 1

DESCRIPTION – ACCESSORIES

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT 4, VENDORTO PREPARE DETAILED DATA SHEET

REMARKS

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

24

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A25

WIND SOCK

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

WIND SOCK TISSUE OUTDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

AS PER HSE-OS-ST20 - FLUORESCENT ORANGE COLOUR UV PROOF TYPE./ STEEL RING FITTED COMPLETE WITH ALL NECESSARY ROPES, SWIVEL HOOK AND READY TO USE. WIND SOCK LIGHT SHALL BE PROVIDED

DESCRIPTION – ACCESSORIES

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT 4, VENDORTO PREPARE DETAILED DATA SHEET

REMARKS

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

25

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A26

RESCUE BASKET FOR WORK AT HEIGHT EMERGENCY

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

RESCUE BASKET FOR WORK AT HEIGHT EMERGENCY OUTDOOR NOTE 3

OPERATING CONDITIONS

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

VENDOR STANDARD

DESCRIPTION – ACCESSORIES

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT 4, VENDORTO PREPARE DETAILED DATA SHEET

REMARKS

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

26

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A27

SAFETY HARNESSES

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

SAFETY HARNESSES OUTDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

SAFETY HARNESSES FOR WORKING AT HEIGHT WITH SHOCK-ABSORBERS AND DOUBLE LANYARD SPECIFICATION AS PER ADNOC PERSONAL PROTECTIVE EQUIPMENT STANDARD HSE-OS-STE02

DESCRIPTION – ACCESSORIES

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT 4, VENDORTO PREPARE DETAILED DATA SHEET

REMARKS

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

27

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A28

FIREMEN’S EQUIPMENT SET

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

FIREMEN’S EQUIPMENT SET OUTDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

THE EQUIPMENT SET SHALL INCLUDE AS MINIMUM THE FOLLOWING:

• FACE-SHIELD, SAFETY, INDUSTRIAL (HELMET MOUNTED FACE SHIELD) - PANORANIC FACE SHIELD WHIT ENHANCED VISION
• COVERALLS (RED COLOURED) , SAFETY, FLAME-RESISTANT JACKET (MEN) SPECIFICATIONS

DESCRIPTION – ACCESSORIES

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
4. VENDORTO PREPARE DETAILED DATA SHEET

REMARKS

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

28

of

30

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A29

SCRAMBLE NET

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

SCRAMBLE NET OUTDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

MATERIAL MESH SIZE LENGHT

POLYPROPILENE ROPE AND POLYAMIDE NYLON ROPES OF 18mm OR 20mm 10”x 10” 18m

DESCRIPTION – ACCESSORIES

FRP CORES OF 50 MM OUTER DIAMETER WITH PU FLOATS IS REQUIRED ONE END OF THE NET IS PROVIDED WITH THREE SPRING HOOKS AND DEE SHACKLES THE NET SHALL BE PROVIDED WITH DISTANCE WHEELS OR SIMILAR TO PREVENT NET FROM TOUCHING THE VERTICAL SURFACE SCRAMBLE NET SHALL BE APPROVED BY EU MARINE DIRECTIVE/UNITED STATES COAST GUARD (USCG)/SOLAS / ABU DHABI COAST GUARD”

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH.
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT
4. VENDORTO PREPARE DETAILED DATA SHEET

REMARKS

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

29

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A30

CHEMICAL KIT BATTERY ROOM

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

CHEMICAL KIT FOR BATTERY ELECTROLYTE INDOOR NOTE 5

OPERATING CONDITIONS

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

DESCRIPTION – ACCESSORIES

DIMENSION (m)

CONTENT

WIDTH*

LENGHT* PLEASE ALSO CONSIDER CHEMICAL KIT SUITABLE TO BATTERY ELECTROLYTE FOR INDOOR APPLICATION. IT SHOULD CONTAIN THE FOLLOWING: 2 NOS. OF APRONS 2 NOS. OF FACE-SHIELD 2 NOS. OF HAND-GLOVES 2 PAIRS OF GUMBOOT

HEIGHT*

MOUNTING

WALL MOUNTING CAPABILITIES WITH HANDLE AND BRACKET.

CABINET

GRP WITH HINGED FRONT OPENING DOOR. DOUBLE DOOR OPENING

CABINET COLOUR

GREEN

COMPLYING TO EN TESTING & STANDARD. CERTIFICATE OF COMPLIANCE REQUIRED

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. THE RATING OF THE ELECTRICAL SAFETY EQUIPMENT SHALL BE SUITABLE FOR THE EQUIPMENT WITH THE HIGHEST VOLTAGE RATING
4. TO BE PROVIDED BY BUILDING SUBCONTRACTOR 5, REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

30

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A31

MULTIPLE GAS DETECTORS

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

PORTABLE OUTDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

DESCRIPTION – ACCESSORIES

(HC, O2, H2S, CO, SO2) (5 gases detector) for Gas detection / testing, with pump test dock and AGT training. (HC, O2, H2S, CO, SO2) (5 gases detector) for Gas detection / testing, with pump test dock and AGT training.

• Audible/visual alarms on activation, sensors, battery, pump and circuitry (continuous)
• ATEX – CE EX II 1 G Ga Ex ia IIC T4
• IP66/67

DESCRIPTION

COMPLYING WITH EMC Directive 2004/108/EC

TEST

REMARKS

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

31

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

APPENDIX 1- A32

PORTABLE MULTIPLE GAS DETECTOR WITH ALARM

VENDOR’S MODEL * TYPE STORAGE LOCATION QUANTITY:

PORTABLE OUTDOOR NOTE 3

AMBIENT TEMPERATURE

°C

3 MIN 58 MAX

BLACK BODY TEMPERATURE : 85

HUMIDITY ATMOSPHERE

DESIGN RELATIVE TEMPERATURE FOR EQUIPMENT IS 100%. MARINE, SALIFEROUS, DUST & SAND

OPERATING CONDITIONS

Portable Multiple Gas Detectors, Rig Rat (HC/O2/H2S/ CO)

DESCRIPTION – ACCESSORIES

DESCRIPTION

COMPLYING TO EN TESTING & STANDARD. CERTIFICATE OF COMPLIANCE REQUIRED

REMARKS

TEST

1. VENDOR TO PROVIDE / CONFIRM INFORMATION MARKED WITH *
2. INSTRUCTION LANGUAGE & NAME OF EQUIPMENT - ARABIC & ENGLISH
3. REFER TO QUANTITIES SPECIFIED IN THE DOC. N. 1-CF0000-40-MOR-0042-00 - MATERIAL REQUISITION FOR SAFETY AND LIFE SAVING EQUIPMENT

DOCUMENT CLASS – 1

SAFETY AND LIFE SAVING EQUIPMENT SPECIFICATION

CF0000-1085351

B3

Sheet

32

of

32

Uncontrolled When Printed

1-CF0000-40-SPE-0032-00

Contractor Document Number

REV

Project: Q-32855 - Saipem Hail & Ghasha Folder: Reference documents